Відео

I know this video is old but where do you get the replacement rubber bushing?

Very easy to follow concise instructions, with no BS. Great job Sir, thank you.

Mine didn't come with the mounting plate for the atv

Love to see this put together as a 48” unit

Those push tubes need to be about 6” longer I have a Honda 520 and the plow is two close to the front of the bike

Why dont you make one for the midsize Ranger?

What a terrible terrible product so to instructions. Stop buying crap from china with poor instructions.

This guy here saving us all some BS hahah thanks guy

Can you install the atv one on a polaris rzr trail premium 2023?

What is the steel strap with the 6 holes in it for...I don't see it anywhere in your video

Glad i found this before trying the instructions 😂 instructions are only good for checking which bolts to use besides that this guy is way more easy to follow. Still took me like 2hrs start to finish lol

You were doing great until you left out the information everyone is looking for concerning the mount to the atv. Ffs!!!

I got the UTV switchblade it’s the same but adjustable 60” up to 74” . This year I’ve put it on my 2023 Honda pioneer 520 as a 60” setup without the push tube extensions. Last year I used it on a parking lot on an s10 Jimmy as 74” with the push tube extensions .

For Kawasaki Teryx...the square ubolts...need about 1/2" extra clearance on the slots right where the plow arms would come up. The only one shown in the manual is for the mule. You guys have the clearance on the inside gap where the arms would come up...but if you guys would cut those slots a little longer open...then boom. As it stands...tomorrow will involve so drilling. :/

Recently bought one of these plows good quality product but everything was labeled wrong number wise had to put it together without directions Customer service does not respond to emails Good product bad attention to detail at manufacturing

I am trying to put the plow blade hinge pivot plate between the vertical supports and it does not fit. No idea what I have wrong. Any ideas?

this silver plate is backwards to my strm chsr, 2016s also need 2 spacers on left, manual sucks, this vid skis steps cmon.....

I don't even like mounting IKEA furniture. Can you imagine?

Yo lo compre muy bueno todo pero lo intale con 2 piesas de aluminios por dentro y 4 tornillos de 3/8 que perfora la parrilla y quedo como una roca con lo que traia para aguantarlo me parecía muy devil Gracias por el videos 👍👍👍

omg why didnt u sho0w the mount??

u didnt show mounting the mount?

Worst instructions ever, none of the part numbers matched up

To bad this doesn't come with a front mount system and a power angle.

😂😂😂😂😂😂😂😂

Nice I am purchasing one

Wonder how heavy it makes dropping the tailgate loader...

Me too!

Do you have a rack for a 2020 kawasaki teryx?

the video is as useless as your mounting instructions

It's Fairlead not Fairlane

Everybody keeps joking at me for getting one because we don't get much snow where I live I tell them it can be used for other stuff

Less than impressed with mine which I have on a cf moto z force 500.u bolts won't stay tight and break easily.mount moves forward and back.cant find replacement u bolts anywhere

Can you please make a video for a cfmoto zforce 500 trail eps..

Doo doo

Hurt fretter run to rrtr

Will this fit a 1999 honda 300 fourtrax

at 4;48, he tells you to tighten the pivit bars up, don't tighten them, just snug them so the thing pivots. when it is caked full of snow and ice and your freezing your ass off outside trying to loosen the bolts, you will thank me

at 3 minute mark of this video, do not tighten up the bottom bolts , you will have to loosenthem again to get the next step done

Love my kolpin plow on my vector 500 this thing pushes snow almost as good as a truck well worth it yah get what yah pay for go kolpin now for a gun boot and trail hunting

Missing how to take it off.

I have plows on a 1990 Honda FourTrax 300 and a 2001 Honda FourTrax 500 (Rubicon). The plows are branded by CMP and Moose but CMP (Cambridge Metal and Plastic) actually manufactured both of them I think. Both ATV’s are still in operation with their original plow blades and mounting hardware. And both have spent many hours plowing many driveways here in Minnesota, especially the older one. After watching this video, I’m glad I didn’t buy that bolted together lightweight Koplin plow. It doesn’t look to me like it would hold up to the rigors of the plowing that my CMP plows have. The CMP plows are constructed of heavier gauge all steel construction. And the plow blade and push tubes are all single welded together assemblies. Sure, you can’t pack them into such a small box so they’re cheaper to warehouse and ship, but I’ll bet mine are a lot stronger and they have stood the test of time. I’ve gone through at least 5-6 1/4” X 3” X 60” steel reversible wear bars in the older plow. So it’s seen a lot of use. I know someone is going to accuse me of shilling for a competitor of Koplin. Not true. I’m just an ATV owner in snowy Minnesota. in fact I own some Koplin accessories and generally have a high regard for their products. Just not this one.

Great vid. Awesome product and ALOT of metal and engineering for the price 👍

I bet 90% of the hate on this plow is from a competitor and/or disgruntled customers who used it wrong/ couldn't figure out how to put it together.

Thanks very much I'm putting on a 2014 Can-Am Outlander 1000 Max Limited the directions are kind of a pain in the ass I was able to get this done in about 45 minutes to an hour with your video thank you making it easier!

Could I mount this to my American Landmaster L7 UTV? It is basically the same front end with the wrench like the ATV in your video. I just want to make sure it will work before I purchase one. Thanks

Your video was decent, you need to be more specific about which piece of hardware goes where. I had to jump back and forth between the video and the instructions because you didn’t tell me the exact nut or bolt that I needed.

How do u installed the switch onto the handrails?

The hardest part about this install is the plate that connects to the atv frame (near impossible to install with skid plate, I had to leave my skid off.) And the winch that they sell with these is not the quick connect ones. After a day or two of cursing in the garage it's installed and it works well.

I put it together your way and it's rong for under my can am I broke bolts

The angle of the plow front to back look horrible? The whole plow frame Needs to be way lower to be level for the plow to stay on the ground. I’d you have bigger tires or tracks this would be 10x worse because there looks to be no adjustment for height? Do you have add ins that fix that or how does this work at all? It looks like the plow will dig straight down like a bulldozer angled into the ground